Sunday, January 29, 2012

Rattle.


I was surprised that the brake cable I thought was snapped wasn't it had slipped from one of the anchor point, even so I make sure those are done up tight so I'm a little confused as to why this happened, It would take some serious force coupled with significant wear to actually allow it to snap.
I disconnected both ends and cleaned them up from grit and crap and put it all back together and gave it a little bit more to be sure, I changed the rear running light and decided it was too hot today to head out, next weekend will be much cooler, so I can get a good run then.
I have read that the rattle sound you can hear in the short video is normal, but would be happy to find a solution if someone knows of one. 

Saturday, January 28, 2012

First hit out.

At a balmy 33 degrees C I decided it was time to go for a ride. The speedo read 4424kms.
How did it go? Well it wasn't my best ride out.
The engine ran well, strong and I didn't take it past 60km or 1/2 throttle, up hills, different revs, through all gears, no problems.......what I was having problems with was the idle, it was like it was gradually getting faster and if I stopped to adjust it the engine would die until I turned the idle back up, and there was a lag in the acceleration and a few things that pointed toward possibly an air leak and a gear adjustment, so after 30kms I headed home.
What I did included, adding about 50-75ml of gear box oil, the plug was a light brown colour and dry and I noticed the engine was a lot hotter than I remember the last cylinder and head ever being, I turned the fuel air mix screw out 1/8th of a turn to see how it goes on the next run, I re-torqued the carb down and noticed that there was some soot and leaking at the base of the head and around the exhaust port, so I re-torqued the head and exhaust as well, I also found that the one of those little screw tops off the end of a spark plug was sitting just below the plug hole in the head, it was in between the fins, but would have caused some trouble had it ended up in the cylinder. I gave the whole engine a clean, the wheel and tyre as well, and left it to cool down properly.
I went back a few hours later and kicked it over, first kick, being on dusk the lights were bright and I had blown the rear running light, the first globe since I did the wiring, and I pushed down on the brake lever to see if the brake light was ok and the cable went snap, FFS. That's a job for tomorrow. The light was fine by the way.

Thursday, January 26, 2012

Australia Day

I had an issue with height regarding the top of the rear shock mount, I didn't realise until I started to fit the airbox. I resorted to using the shorter spacer that was on there and will pick up a new one, it was odd that the new spacer and the new rubber buffer thing had miss matched thread sizes. Anyway, since I was there I decided to replace the main engine mount bolt as well, there's a photo below, I cleaned out the hole as best I could and it also gave me a chance to have a look in there behind the mount, the frame was ok, a little messy though.That all back together I fit the airbox and carb, set the carb up and then on to the kit. you'll notice the rings have a chamfer on it, not sure if this is the case normally, but there is a lot of talk about chamfering ports so the rings don't catch, my thought is that the rings being chamfered is the manufacturers way of counteracting this practice. I put the rings on the piston and oiled it up good and positioned it in the cylinder where it would normally sit and spent ten minutes pushing and pulling it to see how it felt.
I then installed the gasket, cylinder and then the studs, piston and rings and after lapping the head to be sure, it went on too. Job done.
after I put the cylinder cowl and flywheel cover on it was ready for a kick.
Fuel on, choke out, kick nope, kick, nothing, the kickstarter was noticeably harder to kick and felt smooth though, I went on to kick 8-9 times before I began to.start thinking about trouble shooting.
First thing I did was change the 7 plug to a new 6 one and gave it another go, on the second kick I got a splutter, third she kicked over. Gold
The idle was steady and the exhaust was louder, the vibration was strong and there was another rattle that wasn't there before, from the engine and the headset rattle was more pronounced, I let it run for 10 minutes to warm up a bit and turned it off before I died from 2T fumes. it was about midnight by this time so I called it a day.
In the morning of Australia Day, I wheeled it out into the sunshine and kicked it over, second kick, and let it idle while I cleaned up the workshop, put all my tools away or back into the scooters tool box, swept up, changed the oil bottle over for the mineral stuff and I then took her for a spin up and down the driveway a couple of times, now the driveway is about 150 metres long so I got up to about 30kmph in second and  ran out of space. The feel of the bike was totally different and solid, the pull in first is very noticeable, second as well and it has a louder crackle sound than before too.
I'm running 2.5% mineral oil in the tank. there is no specific information in the kits instructions about oil, plugs it recommends everything be clean....really.
The plan is to put a 7 plug back in and take it out over the weekend to max half throttle and just put some kms on the clock, I plan to ride it like normal for a few hundred kms and go to three quarter throttle for the same and then away I go. I don't plan to wait for 1000 kms, I just won't take it on the open highway for a while and just see how it goes. fingers crossed.



Monday, January 23, 2012

DR177 in da house

The cylinder kit arrived first thing this morning, a few days early too.
With it comes the nervous excitement of doing my first kit installation and most likely my first real run in. A quick online search will soon have the uninitiated swamped with information on the best way to do it.
Basicly two schools of thought. Gently gently or ride it like you stole it. and each method then breaks into a number of differing methods and it goes on and on.
I will read the manufacturers recommendations and incorporate my method, based solely on my research and opinion and I should be rolling in no time.
The Box

Kit unpacked and waiting

Old 150cc Piston and new 177cc, not much difference hehehe

The gasket on the bottom came with the kit, it had a significant crease in it, fortunately for me, I'm paranoid of something going wrong and like to have a spare just in case.

Just a comparison

Same

A new style of fuel/air screw, because of it's location I think I'd prefer the old screwdriver head, thread on the new one is finer too

I chose the DR177 over the other kits for a number of reasons, firstly it is not classed as a racing kit but more of a simple bolt on kit that gives you a little bit more ooomf over the standard 150cc engine. Its a cast iron kit that if, god forbid, I do seize up, I can put my newly learnt Vietnamese phrase "để vì lợi ích fucks"...and I can have it machined out and it can still be used, some of the other kits are aluminium and if you seize one they become an expensive paper weight.
Another reason is that other than chamfering the ports so the rings don't catch, I don't need to do any porting work on the cases. price was a factor also, but not the deal breaker.
The first thing I did was fit the airbox and gaskets, then the carb, throttle and choke.
The 24/24 came with a 55-160 idle jet and a 160-BE3-118 main jet stack, this seems to be what most people that have this kit seem to run, with the exception of the main jet being one or two points bigger or smaller. I have a 120 that I might put in initially and run slightly rich for the first run, I plan to use a B7HS plug, but have an 8 and 6 to try also. Tonight I will chamfer the ports, give the cylinder a good clean fit the gasket, cylinder, rings and piston, and get as far along as possible depending on time.

Saturday, January 21, 2012

Rear shock mount.

Since I had the tank out I thought I'd check out the rear shock top mount, for the lower one, I put an 8mm bolt in ages ago when I pulled out the one that was in there, bent, rusted and ground down from 10 to 9mm to fit.....
Anyway, no surprises the spacer was cut and about an inch shorter than the new one I had and was rust covered, as was the spring washer and washer, there was a few washers and a spring washer missing, according to the Haynes Manual exploded drawing. The rubber was a good inch taller than the stock rubber, probably why they cut the spacer, and was quite clearly in place when they sprayed the SPV green as the top side was red.
I threw most of this in the box of crap, cleaned up the tall nut as I couldn't find a nut to fit. So I re-used it.
A side note  is I'm not sure if this is the case on a regular non-asian resto, but just about every fking nut, bolt whatever is different, up down up down changing spanners and sockets, if only I knew how to say for fucks sake in Vietnamese.....
I gave the spring and dampener  a good clean, degreaser and then petrol to be sure, some of the crud is too dense and entrenched for degreaser alone, replaced the lower bolt and nut, gave the case I could now get to a clean too.
Put the tank back in and took a look at the tools strewn all over the place, decided to sit for one beer and called it a night. Workshop can wait until tomorrow for a tidy up.
Note. I am not an employee of Coopers brewery, the bottle cap was there because I was in the zone and forgot to throw it straight in the bin. Not an advertising sideline, but if Coopers brewery need to tap into the scootering market, I am available.

Thursday, January 19, 2012

World tour.

The FedEx tracking shows my box left Freisling, Germany and stopped in Paris, Guangzhou, Singapore before arriving in Sydney, it's now on it's way to Melbourne and eventually to me, they estimate the 27th, but I'm fairly confident that it will be here before then, hopefully on the 25th, so I can spend the Australia Day public holiday getting it all back together, as well as having a barby with prawns and lamb chops, drinking beer in my bluey and stubbies and watching cricket, but that goes without saying.
In the meantime, on the tinkering front......






I've been cleaning, replacing some hardware and a few other things.
Pictures are:
1 - new and old screw for securing the arr box to the case.
2 - where the airbox sits looks like it has been ever so gently shaped with a bastard file.
3 - I had to dremel out the hole to accommodate the new screw, not with a surgeons precision but it's functional.
4 - The old trunnion is what was holding the end of the throttle cable to the arm on the carb. the shiny new one will be relieving it of its duty.
5 - The choke handle has seen better days as had the choke cable inner and outer, the handle will stay but the cables have been replaced.

Sunday, January 15, 2012

Waiting game.



The FedEx tracking service tells me the 25th so I'm just sitting tight and finding something to do,  The carb will come off and I'll clean up the airbox etc.
Cases are together, oil in, stator on and reset 3 degrees closer to TDC. I am going to have another look at the front brake and the horn to see if I can't get them right too.
Otherwise.......
When I was cleaning I noticed that what I first thought was just a line of dirt where the cowl rubber sat, was actually a groove worn into the paint, speaks volumes for the quality of the paint when rubber can wear a line through it in twelve or so months.

Tuesday, January 10, 2012

Getting to know you.

My first box of parts arrived today, so it's back to re-assembling the engine, the last couple of days has been spent just cleaning in the areas that are normally harder to get to., I have given the cases a good clean out as well, and I was surprised of how much general crap there was considering it should only be oil and the material that comes from metal wearing. I have since examined everything closer and found signs of wear that I am guessing would be normal but leaving the components still serviceable.
I'm not ready to go down the road of a full engine rebuild, the crank should probably be replaced and the con rod has a bush in the end where a caged needle bearing should be, confirming what some people have questioned in the past that some, or maybe more, of the engine is from a -----.
I don't have the funds to proceed with dropping the engine and overhauling what's left, I pushed the friendship with the wife spending on parts for this engine work as it is, the thing is I also don't want the scooter just sitting there in bits looking at me wondering when I was going to be riding it again.
This decision may have already made for me depending on how it all goes back together, a few days will tell.
Some pictures.





First three are just comparison between parts.
Four is the wear caused by the worn kick start gear.
The last is the collection of case nuts next to a new one, I omitted the 3075 washers, I used new washers, lock washers and nuts all round.
Last night I put the new kickstart components in and carefully installed the new case gasket with gasket cement, now I had a gasket set I was certain was a three port, that's what I ordered, over a year ago and it wasn't until recently I discovered it was a for a two port, so I needed to change it a little so it would fit, just cut the top of it to allow for the third port and one bolt hole that was about an inch or so from where it should be, no dramas.
The case went back together no problems, next was the gears selector gasket and I greased up the gear selector and put it back on, I then hooked up the gear cables and roughly located them and called it a night.
Next up will be the stator, it was set at 22 degrees BTDC, the kit, a DR177, is recommended to be set at or around 19 degrees, I'll hook the wiring back up and hopefully the kit arrives by the end of the week.

Friday, January 6, 2012

Gear box




Much to my surprise, the gearbox was in pretty good condition, the cruciform wasn't worn, all the gears were in good condition, the only downside to my untrained eyes was the plate at the back of the christmas tree had some surface rust and was obviously old and the case stud in the bottom picture is held in by some sort of liquid nail type substance. All in all I was happy with what I could see, so I cleaned it up and once the new parts arrive I'll put it all back together, I'm guessing that all my parts and the new kit,  the new 24/24 carb and the few odds and ends will be here by next weekend, In the mean time I will be giving Gloria a good once over service and a wash. 
A good result all round, cue sigh of relief.
One thing I noticed while pulling the case apart was the amount of washers the guys used and have used on other parts of the scooters, literally hundreds and the quality couldn't be lower, they are paper thin which is probably why they use so many.....

Kickstart





Next cab off the rank, the kickstart set up.
Top photo is the chip off one of the teeth, must have happened before I got the scooter as I would assume that I'd either find it in the case or it would've been chewed up by the gears or worse....anyway, none of that happened, it will be replaced anyway.
Second one is the rubber stopper worn to within an inch of its life, I flicked the opposite one in pic three to show what it should've looked like, they are both old and hard as rocks, replacing these too.
Finally the starter gear, it is a little worn and most likely the cause of the kick start slipping, it's on the list too,

Gear Selector




I started off by draining the oil, it was 950kms old and the usual grey colour, a few very small flecks of metal, normal stuff, I dropped the exhaust and pulled the cylinder head and barrel off, I noticed there was little resistance from the head nuts and there was some fuel/ oil kind of leaking from the head, this explained the most likely reason the bike was running ok but progressively getting harder to start was the lack of compression, not helped by me flogging the old girl the other week to see just how fast I could go
Since I cleaned it up last time, there was evidence that the rings just weren't doing their job, there was dark marks down the sides, out of interest I changed the old rings for the third oversize ones I had, the gap was a hell of a lot bigger than the maximum .35 the manual suggested. My decision was made for me. I ordered a new cylinder kit and it's on its way, I'll go more into the kit later.
I put the piston, cylinder, rings and head in a bag and put it on a shelf, I realise I could've just re-torqued the nuts and it would've been ok, but another bandaid wasn't going to fix it for ever.
So on to the gear selector, I took the kick start lever off, it was old and worn as expected, the spline was still in ok condition so it will go back on later. after I cleaned all the grease and crud off it, it's tyre colours began to shine, it would appear the tool of choice was an angle grinder and things are a little bent out of shape, nothing a hit with the dremmel won't fix, it is still solid, moves true and firmly, this too will get a good greasing and be put back on.

Thursday, January 5, 2012

The final frontier.

I think the GPS speed trial did nothing for the engine on the Sprint V, everyday since starting the engine got harder and she went from a 2-3 kick bike to a wont start at all bike and the kick start was slipping more and more
A perfect excuse to fix something, I sat in the workshop last night after I built a small ramp to get the scooter in over the door step....I think it's time.
I am slightly nervous about splitting the cases, but also excited. A little concerned that I will find some more dodgey shit as well.
So I made a plan.
Pull the head and cylinder off and replace it with a new kit.
Pull the gear selector off and clean it up.
Split the cases and replace the kick start internals regardless of condition, have a really good look at the rest and see where I go from there. I'll replace the hardware as I go, the cruciform as well and with the kit I will need to alter the timing so I can give the stator an overhaul, check the points gap etc. As long as all is ok that's as far as I will go, time will tell.